View LHRFUG2093-R2-PF_4695099.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only
DUAL COLOR LED LAMPS
Pb
Lead-Free Parts
LHRFUG2093/R2-PF
DATA SHEET
DOC. NO : REV. DATE : :
QW0905- LHRFUG2093/R2-PF-0808 A 17 - Aug. - 2009
DCC
LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only
PART NO. LHRFUG2093/R2-PF Page 1/6
Package Dimensions
3.0 4.0
4.2 1.5 MAX
5.2
6.70.5
HRF
UG
0.5 TYP
18.0MIN
123
2.0MIN 2.0MIN 2.54TYP 2.54TYP
1.ANODE RED 2.COMMON CATHODE 3.ANODE GREEN
1
2
3
Note : 1.All dimension are in millimeter tolerance is 0.25mm unless otherwise noted. 2.Specifications are subject to change without notice.
Directivity Radiation
0 -30 -60 30
-60
100% 75% 50%
25%
0
25% 50% 75% 100%
LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only
PART NO. LHRFUG2093/R2-PF Page 2/6
Absolute Maximum Ratings at Ta=25
Ratings Parameter Symbol Red Forward Current Peak Forward Current Duty 1/10@10KHz Power Dissipation Electrostatic Discharge( * ) Reverse Current @5V Operating Temperature Storage Temperature IF IFP PD ESD Ir Topr Tstg 25 75 65 2000 10 -40 ~ +85 -40 ~ +100 Green 25 75 65 mA mA mW V UNIT
A
Electricity or power surge will the Use of anti-electrosatic * Static is recommended when handingdamageLED.LED.devices, a conductive wrist band or must be properly glove these All equipment and machinery grounded.
Typical Electrical & Optical Characteristics (Ta=25 )
PART NO
MATERIAL Emitted AlGaInP Red
COLOR Lens
Forward Luminous Viewing Dominant Spectral voltage intensity wave angle halfwidth @20mA(V) @20mA(mcd) 2 1/2 length nm Dnm (deg) Min. Max. Min. Typ. 630 20 20 1.5 1.7 2.4 2.6 350 160 550 300 30 30
LHRFUG2093/R2-PF
Water Clear AlGaInP Green 574
Note : 1.The forward voltage data did not including 0.1V testing tolerance. 2. The luminous intensity data did not including 15% testing tolerance.
LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only
PART NO. LHRFUG2093/R2-PF Page 3/6
Typical Electro-Optical Characteristics Curve
HRF CHIP
Fig.1 Forward current vs. Forward Voltage Fig.2 Relative Intensity vs. Forward Current
60
2.0
Forward Current(mA)
40 30 20 10 0 0 0.5 1.0 1.5 2.0 2.5 3.0
Relative Intensity Normalize @20mA
50
1.0
0.0 1.0 10 100 1000
Forward Voltage(V) Fig.3 Forward Voltage vs. Temperature
Forward Current(mA) Fig.4 Relative Intensity vs. Temperature
Forward Voltage@20mA Normalize @25
Relative Intensity@20mA Normalize @25
-20 0 20 40 60 80
1.2 1.1 1.0 0.9
2.5 2.0 1.5 1.0 0.5 0.0 -20 0 20 40 60 80
0.8
Ambient Temperature()
Ambient Temperature()
Fig.5 Relative Intensity vs. Wavelength
1.0
Relative Intensity@20mA
0.5
0.0 550 600 650 700
Wavelength (nm)
LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only
PART NO. LHRFUG2093/R2-PF Page 4/6
Typical Electro-Optical Characteristics Curve
UG CHIP
Fig.1 Forward current vs. Forward Voltage
60
Fig.2 Relative Intensity vs. Forward Current
2.0
Forward Current(mA)
50 40 30 20 10 0 0 0.5 1.0 1.5 2.0 2.5 3.0
Relative Intensity Normalize @20mA
1.0
0 1.0 10 100 1000
Forward Voltage(V) Fig.3 Forward Voltage vs. Temperature
Forward Current(mA) Fig.4 Relative Intensity vs. Temperature
1.2 1.1 1.0 0.9 0.8 -20 0 20 40 60 80
Relative Intensity @20mA Normalize @25
Forward Voltage@20mA Normaliz @25
2.5 2.0 1.5 1.0 0.5 0 -20 0 20 40 60 80
Ambient Temperature()
Ambient Temperature()
Fig.5 Relative Intensity vs. Wavelength
Relative Intensity @20mA
1.0
0.5
0 500 550 600 650
Wavelength (nm)
LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only
PART NO. LHRFUG2093/R2-PF Page 5/6
Soldering Condition(Pb-Free) 1.Iron: Soldering Iron:30W Max Temperature 350 C Max Soldering Time:3 Seconds Max(One time only) Distance:2mm Min(From solder joint to body)
2.Wave Soldering Profile Dip Soldering Preheat: 120 C Max Preheat time: 60seconds Max Ramp-up 2C/sec(max) Ramp-Down:-5 C/sec(max) Solder Bath:260 C Max Dipping Time:3 seconds Max Distance:2mm Min(From solder joint to body)
Temp( C) 260 C3sec Max
260
5 /sec max
120
2 /sec max Preheat
25 0 0
50
100
150
Time(sec)
Note: 1.Wave solder should not be made more than one time. 2.You can just only select one of the soldering conditions as above.
LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only
PART NO. LHRFUG2093/R2-PF Page 6/6
Reliability Test:
Test Item
Test Condition
1.Under Room Temperature 2.If=20mA 3.t=1000 hrs (-24hrs, +72hrs)
Description
This test is conducted for the purpose of detemining the resistance of a part in electrical and themal stressed.
Reference Standard
MIL-STD-750: 1026 MIL-STD-883: 1005 JIS C 7021: B-1
Operating Life Test
High Temperature Storage Test
1.Ta=105 5 2.t=1000 hrs (-24hrs, +72hrs)
The purpose of this is the resistance of the device which is laid under condition of high temperature for hours.
MIL-STD-883:1008 JIS C 7021: B-10
Low Temperature Storage Test
1.Ta=-40 5 2.t=1000 hrs (-24hrs, +72hrs)
The purpose of this is the resistance of the device which is laid under condition of low temperature for hours.
JIS C 7021: B-12
High Temperature High Humidity Test
1.Ta=65 5 2.RH=90 %~95% 3.t=240hrs 2hrs
The purpose of this test is the resistance of the device under tropical for hours.
MIL-STD-202:103B JIS C 7021: B-11
Thermal Shock Test
1.Ta=105 5&-405 (10min) (10min) 2.total 10 cycles
The purpose of this is the resistance of the device to sudden extreme changes in high and low temperature. This test intended to determine the thermal characteristic resistance of the device to sudden exposures at extreme changes in temperature when soldering the lead wire.
MIL-STD-202: 107D MIL-STD-750: 1051 MIL-STD-883: 1011
Solder Resistance Test
1.T.Sol=260 5 2.Dwell time= 10 1sec.
MIL-STD-202: 210A MIL-STD-750: 2031 JIS C 7021: A-1
Solderability Test
1.T.Sol=230 5 2.Dwell time=5 1sec
This test intended to see soldering well performed or not.
MIL-STD-202: 208D MIL-STD-750: 2026 MIL-STD-883: 2003 JIS C 7021: A-2

▲Up To Search▲

Price & Availability of LHRFUG2093-R2-PF

	To Download LHRFUG2093-R2-PF Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .